Fault Codes needed for Hotpoint Aquarius FDW60?

Thank you so much, thought dishwasher was a gonna! Tilted it 45 degrees to the left , nearly sobbed when yet more water poured on the floor. Also tightened up lower spray arm and it's working.....yeaaahhhh thank you .

Cynthia
March 2017

Eco 45 flashing light problem. Tilting 45 degrees worked a treat. Machine working again and my family think I'm a marvel. Thanks to all and Happy New Year

Chris
January 2017

I have a fdw60
It just beeps when selecting a programme no flashing lights
On any programme and doesent run
Just beeps back at me
Anyone any ideas ??

John
May 2016

I had two fault lights Eco and prewash. Followed these guides. Ended up following a YouTube video showing me how to remove the pump and check for debris. Turned out there was a tiny piece of chipped plate blocking it. Put it back together and now working fine.

Mark
October 2015

Thank you all who have posted regarding ECO 45 flashing & tilting to left by 45 degrees - It does let out a lot of water but it works, thanks for saving me a hefty call out charge

boogaloo
September 2015

Fair play to you guys ,had the same flashing light fault .The plastic screw located on the bottom tray was loose.All you need to do is as already described :
1)pull the power lead out of the socket
2)unscrew the bottom plastic screw which is located inside of the dishwasher on the bottom tray
3)prepare a mop or some cloth
4)Tipp dishwasher over on the side to drain the water
5)place the screw with spray arm back and try to turn the dishwasher on

Good luck my problem is sorted ,thanks a million guys

Sasha
May 2015

Craig 2010 absolute star!!

Had eco light flashing and dishwasher wouldn't fill...tried looking at all the user manuals which don't cover this fault and then found this thread. Had a few blockages in the spray arms (whether coincidence or not, not sure) but tilted machine 45deg to the left and hey presto it's now working. Took all of 30 seconds to fix.

Thanks again, almost thought I was having to buying a new machine.

Shane Knight49
March 2015

Read teasers note tried the small pump no debris reconnected and started programme but again to no avail,
Last effort before hefty repair bill leant machine as you look at face to left 45% hey presto !
Is there some sort of level switch that may of jammed?

STUART
December 2014

Hi

I had a similar problem with the Eco and Prewash lights flashing. After this happened within the first minute or so of a new cycle the dishwasher wasn’t draining properly (sounded like the waste pipe hose was just sucking air). I then had the dishwasher on its side to check the drain pump and motor. This all looked fine so I reattached them both, put it through a new cycle but again the same thing keeps happening.

Can anyone suggest if I need to fit a new drain pump or circulation pump? Or even both?

Many thanks for any help given.

Gary
July 2014

I've had a couple of issues with LED's flashing and I saw the advice about tipping the machine on its side. It worked but is a bit messy! What I now do is remove the bottom arm, tightly roll a couple of sheets of kitchen towel into a long length and then stick this down the hole you can see when the arm is off. The capillary action sucks up enough water to mean you don't have to tip the machine and get water all over your kitchen floor - simple but effective :-)

Rob
July 2014

Thanks craig may 2010

30 mins alltogether

Rusty
July 2014

based "Craig May 2010"; put the dishwasher lie down to one side, remove the bottom cover, find the small pump (can easily find out which is linked from the pipe discharging the used dirty water).

remove the three screws (small alan key), don't need to remove anything else, can find something there stopped the pump spinning.

Wu
March 2014

Hey guys

can someone show me what the detector look like? or atleast the anti flood device.... please show me a pic or google image

thanks

george
December 2013

My Eco light was flashing and no water getting into the machine tilted to 45 degrees -- boom working again, fab advice, thought it was gonna be costly!!!

Daniel
October 2013

Thank you to Craig may 2010. Economy wash stopped after it's prewash stage twice. Scooped water out and put dishawasher on it's side. Just found a piece of glass in the drain pump and currently have fingers crossed that machine completes its cycle. Sounds healthier anyway!

Karen
October 2013

FDW60 had rinse and eco lights flashing,
I cleaned filter, tightened lower spray bar, and tilted over, and now its working,
this is a great site, thanks for all the tips, saved ££s

bruce
October 2013

hey i have a hotpoint aquarius fdw70. in the middle of a wash all power died. tried the obvious changed fuse changed socket even put on a new plug but still completly dead... any ideas

deco
July 2013

I have a rinse aid light flashing, I have taken to pump out and cleaned it but found nothing in there. the dishwasher works on any cycle but after a min it starts to leak as the water isn't draining away. Any ideas, someone mentioned two pumps? Any ideas would be great thanks.

Andyuk
May 2013

i have a hotpoint fdw60 dishwasher and two green lights are on, i think is the 1hour and 12hour ones. please help

michael
May 2013

i have the above machine and would like to know which screws i have to undo to change the drain hose which has split

a smith
February 2013

worked a treat with the tipping 45 degrees and tightening the bottom arm. ty guys

gazzer
February 2013

My washer stopped working, the ECo light was flashing and I was clueless. I contacted Hotpoint repair and booked a repair man for the next day, two choices £120 or £14.99 a month for a year. I then read the post by Tesser and within minutes my dish washer now works! The bottom spray arm connection was loose, I tightened it, tilted the washer slightly so excess water ran out of the bottom tray and hey presto. Quids in!!!!!!!!

Gazza..
February 2013

My eco light was flashing so after checking this site out took the back off after tipping to 45degrees to clear the water in the drain tray, checked out the pump and pipework which was clean, tried it again and it started to go through the washing sequence. It got so far and stopped again with the eco light flashing. So checked further back in the forum and found a post from scotquine saying about the bottom spray bar connection being loose. Checked mine and found it loose. That was how the water was getting into the drain tray. Tightened it up and now OK. I wish I had read all the posts to start with as the actual fix took about 30 seconds, after spending an hour or so getting all the covers off when I did'nt need to. Thanks for the forum and scotquine in particular.

Tesser
December 2012

Craig - May 2010, you are a legend. Easy to take the bottom off the dishwasher as you described, and once I detached the smaller pump, I found a piece of a match stick lodged in there which was preventing it spinning.

The dishwasher now works like a treat again. Many thanks for the great advice.

Steve
November 2012

Thanks to Craig in May 2010 - spot on answer. was a piece of glass in ours.

Sue
June 2012

my dishes are not properly cleaned. salt level and rinse aid are both topped up and filter is clean

Ian Parker
May 2012

The ECO 45 light was flashing and the water was not entering the machine . I tipped it to the suggested 45 degree angle and bingo .... it works again - Cheers

Jake Fulton
May 2012

when the eco green light is flashing. (FDW65)

tilt the dishwasher to 45 degrees to empty the eccess water in the sump. this deactivates the float overload sensor. It is likely there is a build up of black slime in the outlet channels below the filters at the bottom of the dishwasher (inside the dish area). Use a vax machine (or power flush device) on "water suck" and suck out all the gunge from the outlet channels. use a bit of flexible plastic to loosen any gunge also. add clean water into the sump and resuck out with the vax. This works well. If it doesnt you probably have a fault outlet pump. hope this helps, Paul :)

Paul johansson
March 2012

Great Advice Craig May 2010.

I have a problem with FDW60. It was doing the double light flash & making funny noises.

first thing I did was to turn of the incoming water hose and run a rinse - this pumped all the remaining water out of the bottom of the DW - therefore I can conclude that the exit pump is working fine.

The problems occurred after that - when I ran a cycle, it started boiling the water and I could hear it bubbling up the pipe just inside the black plastic cover at the back.

It was clear that there was something wrong with the main pump.

I managed to open that up by removing a detector switch on the side and having a poke around - it was spinning freely.

It was then I noticed that the top of a white cylinder near the pump was a bit odd. This cylinder has the power wires attached to it (red & blue).

I removed this cylinder (bolt on the bottom attaching it to the pump housing) and the contents had melted through the side.

So the main pump is not working - explains the symptoms.

Now need to find a replacement part for the "melt-down" and see if that fixes it.

Matt
February 2012

Craig - my old man's dishwasher now fixed, many thanks! He'd thought there was only one pump and was about to pay to get a new one fitted. Turns out that it was the second, smaller pump which had the obstruction (a very rusty screw in this case)

Iain
January 2012

my dishwashers hotpoint no work
plm fast 40c and prewash how much fix work
pay ????

steven lawton
January 2012

hi my dishwashers hotpoint no work
fast 40c and prewash need know ????

steven lawton
January 2012

my hotpoint fdw60 dishwasher, has two flashing lights fast 40 and delicates, it heats up and drains but give a bad wash, any ideas, thanks

G manning
January 2012

Saw this site and thought I had cracked the fault as the indications were the same. However the pump was clear and when I reassembled the pumps and started it up again it showed the same symptoms. Where do I go from here? Has anyone else found these symptoms and what was their next step? I am now suggesting the circuit board is to blame but have now downed tools for the day.

Big_Phil
December 2011

Craig, I had the same flashing lights and not pumping water out and thanks to your advice we took the small pump out and found a pin from one of my knives in there. Put it back together and all working fine.
Many Thanks

Karen
November 2011

Craig,

Your a star - easy peasy fix and you saved me £100.

Thanks,

Noel
June 2011

Hi.
I left my SDW60 running overnight, came down this morning to discover two lights flashing, 4 & 6 (Fast & Delicate).
I checked the filters and they are all fine.
I noticed that other posts here mention tripping out the house electrical fuses. I was sitting at my computer yesterday when we had a blip in the mains power supply, the power went off and came back on in about one second, and I'm wondering if it happened again last night while the machine was washing and that's what caused my problem. I would say though that the machine had completed the wash cycle and everything was clean.
I turned my machine off for a couple of minutes using the On / Off button on the front, and when I turned it back on it had mended itself.

Nigel.
May 2011

hiya
please help me....my dishwasher has decided to just pack up on me. The selecting of programme works fine and push start and it whirs away but thats about it...no water is reaching and going in to continue the wash...it will just flash constantly until u switch it off.
Any advice?

Sally
April 2011

ref.. Dave may2010. Flashing fault lights..

i guess iv just found the same bit of plate blocking the pump that every1 else has found.. Cheers for good advice to an easy fix..

Andy..
March 2011

Had the same error - lights flashing (dishwasher full of water). Followed the advice of Craig May 2010 and found a chip from a broken bowl in the smaller pump. Ran the pre-wash cycle and everything works ok. No flashing lights and an empty dishwasher. Joy :)

PS. It took me about an hour to fix the problem and refit the hoses. And if I can do it...so can you!

Cheers Craig May 2010.

Mike Jones
January 2011

Hotpoint Aquarius FDW65. Eco 45c & Fast 40c flashing together and not shown in the handbook

Exactly like Craig May 2010 took the small pump off as he described and found a cocktail stick jamming it - no more buffets!! - working dishwasher again. Thanks Craig.

Wayne
January 2011

I have an aquarius fdw60. i have the eco light flashing can anyone tell me what it is please

matt
January 2011

For the answer to all the flashing light error codes on this and many more appliances I have writen them down on my web site at http://www.selfix-uk.co.uk just click on the error code heading and follow the instructions on that page. Have Fun!

Dave Selfix-uk
January 2011

I had fast & delicates lights flashing after it took out the RCD.
The machine ran after, emptied, filled and then the main pump started. After a short while the lights flashed and the dish washer emptied.
I took the bottom off and found the heater was badly burned and obviously faulty, so the flashing don't seem to distinguish between faults very well .
Perhaps it's the time the lights come on that indicate the fault, mine was after the main pump operated at the time the heater should come on, others where it is a water fault have come on after the pump runs.

Pete Smith
January 2011

I am soooooo grateful to everyone who has answered on this page!! I had the flashing lights on prewash and eco wash and my hubbyp looked at it and said it was totally knackered!!!! I tried cleaning out the filters and then poured two hot kettles on the filters, switched off at the wall and HEY PRESTO!! a fixed dishwasher!!! just in time for christmas ~ didn't fancy forking out on a new one just a couple of weeks before the 25th!!! many thanks again and happy christmas to all

Scotquine
December 2010

I had the problem with the machine tripping out due the float in the base - it turned out to be a small leak that was comming through around the spinning jet in the base of the machine inside - i tighten this up from inside (about 1.5 turns) and "job done"

Duncan
November 2010

Hotpoint Aquarius FDW60.
Eco 45 light only flashing.
The filter in the washing compartment was blocked with large bits of food. This had caused water to flow into a shallow driptray at the base of the machine. There is a polystyrene float in this tray which rises and trips a micro switch, I presume to stop the kitchen floor flooding. The tray must hold a litre plus, so the best option is to carefully move the machine outside or have a mop and bucket handy, water sloshes out very easily.
Tipping the machine on its side clears the water. This cured the fault, but as stated earlier on this post, a blocked or faulty pump could also be a problem. I ruled the pump out first by tipping a bowl of water into the machine and turned it on to a cycle. The pump emptied the water first before the machine faulted so proving the pump. All is accessible if the machine is on its side or upside down. The tray is held on by six screw, three front and three rear. The two screws directly underneath hold the float switch in place.

Steve P
November 2010

Craig (May 2010) spot on answer many thanks. In my case it was a small piece of glass jamming the pump impeller. Very easy to fix.

Tim
September 2010

I fixed my machine now, very easy and simple. I took the small pump out and cleaned, very dirty you have to clean the dishes before putting them in the dishwacher to prevent this occurring. other thing that i notice was that the ring for the salt deposit was lose so the water was going down and the tray was full which actived the error switch and stop the dishwasher working. Good luck guys

Luis
August 2010

my dishwasher keeps stopping half way through it cycle and delicate light keeps flashing any ideas?

cheers andy

andy w
July 2010

I have eco and prewash lights flashing. Any ideas
Thanks Jen

Jenie
July 2010

Craig (May 2010) thanks a million for your help, you were spot on, the culprit was a small bone, all fixed and me very happy

Storm21
June 2010

When I switch my FDW60 on it only lets me select Intense wash, beeps then the Drying light comes on.

Ian
June 2010

i think fast and delicate lights flashing is an overfill problem.

paddy
June 2010

Had same problem. Tried resetting, unplugging, drain clean out with straws,but no luck. It wasn't until I took the machine outside, led it on it's side, removed the bottom cover plate that I found the problem.

There are two pumps, one which is used to supply water to the components of the machine when washing (the large pump) and a smaller drain pump used to discharge the used dirty water. It was this small pump that was the problem. Its easy to remove just disconnect the small wiring plug from back of pump, disconnect the drain pipe using a pair of pliers to squeeze the hose clamp, remove the single fixing screw then twist to remove.

The pump can then be taken apart by removing the three torx screws and pulling apart. I found a small piece of plastic jamming the impeller on mine, removed it put machine back together and hey presto a working dishwasher. Easy !!!

Craig
May 2010

have a question can switch it on, water goes in ,then it flashes the two lights and then it stops what do i do to fix it

lorraine
May 2010

Help my washer runs for 5 mins then stops lights flash ive tried the straw cleaneing the boiling water the switching off and on but still no luck ive cleaned the sink pipes as well do you think i need to remove the drain pipe under neath now please help someone !!!

Julie
May 2010

Fantastic, cleared error lights 3 and 5 by sitting it on its back, draining excess water downhill, flushing through with boiling water and repeating the above again, now works fine.

urban iceberg
March 2010

Iv got no water coming in my dishwasher & Eco light flashing. The filters are clean so don't know what wrong with it.

Mandy leelee
March 2010

lights are flashing and wont work

gillian
March 2010

I have the Fast and Delicate lights flashing. Cleaned the filters and drained excess water as well as unplugging the mains and still is stoping straight away.
Its not tripping electrics

Nikki
February 2010

had fast and delicate flashing on my fd, filters where clean, outlet was clear,so turned off at mains waited a couple of mins and hey presto worked a treat.

wally
January 2010

I had the eco wash and fast wash lights flashing. I tried the straw, abd also those wooden bbq kebab skewers that look like big cocktail sticks. I could see lots of horrible stuff floating around as I cleared the blockage. I also boiled the kettle, tilted the dishwasher back and poured the boiling water down where the filters are at the bottom of the dishwasher. That seemed to do the trick, lets hope winning the election is as easy.

Gordon Brown
January 2010

Had the same problem with my DW, fixed it by poking around with a straw, tilting it forwards, switching it off at the mains, disconnecting the inlet pipe then re connecting it. Not sure which part solved the problem but have just saved myself £300 to replace the DW. Off to the pub now with the money saved. Cheers

Ian F
December 2009

I have an identical problem to the delicates and fast lights flashing. Tripped electrics too - DW now 3 years old and first major problem with it.

Rob
November 2009

just had this occur to me!
Brilliant, clean out the water poke a straw down to make sure its clear. CLEAN the filters and reapply power. worked perfectly!

Mark Tiana
November 2009

washers working but not getting hot dishes are not clean

duncan
October 2009

Switched off, cleaned filters (also used straw)tilted forward for 2 mins and worked. Thanks

CeeCee
October 2009

hi had the same codes flashing fast and delicates cleaned out the inside filter at the bottom of the machine also with a straw and then tilted the dishwasher forward left for about 2 mins and then turned on and it is working. many thanks

marie
September 2009

I have the same problem and the Fast and Delicate lights flashing means a drainage problem and could be a kinked drainage hose (if you have moved the appliance recently then this could be a reason for it to be kinked) or it could be the filters. This is according to Hotpoint's internal faults web site that we mortals can't see. It could also be the fact that the machine needs resetting and this means just turning the power off at the wall switch for a few minutes and then turning it back on. If this doesn't work then you need an engineer.

Mark
August 2009

I've got different lights flashing. fast & delicate lights flash after a couple of minutes of the machine running. also think the machine tripped the house electrics the other night. anybody got any ideas.

paul of pill
June 2009

echo and fast flashing,water not draining

scott burrage
May 2009

i have a hotpoint aquarius fdw60 two ligth flash on one is the delicate and the other is fasts 40

colin
March 2009

My dishwasher keeps tripping the house electrics and blowing the fuse in the plug every time I switch it on. It has worked fine for over a year now and I have tried other equipment in the same plug socket and they are fine has anyone got any ideas before I call an engineer out.

Steve
February 2009

I have this problem too - Any help yet?

Sam
December 2008

Definetly a blockage, used straws to 'drain rod' the hole in the bottom of the dishwasher and it worked a treat!

Dave
September 2008

i have lights fast and delicate which indicate a heating fault, can anyone tell me if it would be the PCB as sometimes it will do full cycle and other times will cut out straight away.

yami
July 2008

often water still in bottom of machine.tilt machine sideways to tip water out,allow time to dry and cross your fingers ![there is some sort of cut out switch in machine if water is in it].chris

chris
April 2008

same prob i turned it off at the mains and it seems to be sorted

shane
February 2008

ODD!?
The manual states that a blockage is signified by indicators 4 & 5 flashing (Fast 40 & Prewash). Yet I too took out the filters and "pumped" out the excess water (Whilst having it switched off at the mains) and it now works fine too. Maybe it's a typo in the manual and it should be eco 45 and fast 40 lights?
Also, I previously switched the machine off with its own button, maybe it's important to stop power to the washer completely as it renembers the error code unless you disconect power totally.
Below is a link to the manual if it helps.
http://imagebank.indesitcompany.co.uk/brochures_online/pdf/Hotpoint/Dishwashers/FDW60_65_after_Oct04_19505371801.pdf

Dualwolf
July 2007

Not sure if this helps but I believe you have a blocked filter.
I had exactly the same, removed the filter -pulled up the circular beige plastic thing with the triangular metal mesh and under there is a couple of filters- cleaned them all out and all seems ok.

To reset, turn machine off at mains for at least a minute or two and the fault codes should reset.

AndyB
August 2006

YEP i have this problem also....any help yet!

rich
May 2006

Hi,

I have the exact same problem and wondered if you ever did find the answer ?

Thanks,
Michael.

Michael
May 2006