Mend Fellowes Document Laminators

Mend Office Appliances, Document Laminators

Find out how to mend it for free.

Ask Question

Find out how to mend Fellowes document laminators

Related Categories

Mend > Document Laminators

how can i fix Fellowes MARS A4 LAMINATOR?

a a5 pouch has become stuck inside the laminator and am unable to get it out as not visible. only 2 screws underneath which dont seem to undo anything. any ideas to be able to undo cover if possible to get at the fried pouch would be appreciated, as makes a crunching noise when turned on and unable to use, pouch must be stuck some where inside.

erika
July 2009

Fellowes Office Appliances, Document Laminators Fellowes Mars A4 Laminator

Thank y'all so much for the advice, it worked!

Robin, from Georgia
February 2016

Thanks so much to everyone here! The receptionist was about to kill me....

Joe
January 2016

thanks, this saved me! and my laminator :)

Monica
August 2015

Excellent, worked like a charm (see answers below):
----------------------------
There are 4 additional screws under the rubber footings. Pop them off with a knife and then undo the screws.

Stu
April 2010

------------------

You should be able to undo the screws and pop off the white section of the laminator away from the grey plastic.

bec
August 2009

JamesOb
June 2015

great tip thanx worked like a charm...just remember if it got stuck a few minutes back....yes it is still warm...lol!

jo
September 2014

Just fixed my MARS 125 tonight using the instructions in this thread! Thank you all! :D

EB
April 2014

Thanx for the tips! I made my laminator!

Gekkegettie
May 2013

How do you get the cog off? I can't undo the screw!

Frustrated but determined!
February 2013

Stu is 100% correct...thanks man! I was just able to pull out a stuck sheet because I could get off the cover... careful when you pull off the cover that the internal 4 springs do not fall away from their intended position.

Kevin
September 2011

Than you unscrew the motor off the end the unscrew the cog pull the other ine off, the n you should be able to put to get the pouch back out and put it all back together!

Max Hardy
March 2011

There are 4 additional screws under the rubber footings. Pop them off with a knife and then undo the screws.

Stu
April 2010

Your should be able to undo the screws and pop off the white section of the lamiator away from the grey plastic. The plastic is tough though and could break if the plastic tabs don't pop out.

bec
August 2009

Automatic Answer

While you wait for answers, we may have found some information which could help you.

Click here for Fellowes Mars A4 Laminator

Find out how to mend Fellowes document laminators

GBC Ultima 65 laminator?

How can I repair my GBC Pinnacle 27?

How can I mend my Seal RL918 Lamination machine?

the machine shows the red light on, buy that's all. the machine does not ?

my new blusmart laminator dont work when plugged in?

How do I replace a fuse in the 4250?

GBC DocuSeal 95 Roller Won't Turn?

Laminator gbc ultima 65 How to reinstall a power switch?

How Can I Fix a GBC 620 0S,2013?

G5640 Laminator?

How do I stop the overheating of our Ultima 65 laminator?

How to Remove an item from a Fellows Mars A4 laminator?

How to mend ...

howtomendit.com for free repair help, information and advice.

Mend document laminators ...

Mend Document Laminators

Find out how to mend Fellowes document laminators

Mend Fellowes Document Laminators

Related Categories

Mend > Document Laminators

how can i fix Fellowes MARS A4 LAMINATOR?

Automatic Answer

how can i fix Fellowes MARS A4 LAMINATOR?

I can answer this question ...

how can i fix Fellowes MARS A4 LAMINATOR?

How to mend ...

Mend document laminators ...

GBC Ultima 65 laminator?

How can I mend my Seal RL918 Lamination machine?

GBC Ultima 65 not sealing edges?

Call engineer icons?

G5640 Laminator?