how can I fix my flamerite fire model YCT-100?

I can turn the fire on and then the heat on 0/1 but it’s not warm enough. I try to turn on to 1/11 but that doesn’t work on my remote anymore. How can I fix the remote to get the higher heat please. Hope you can help, many thanks

Kerry Shaw
July 2019

I have a villager but it has the same remote as the yct-100.
I couldn't switch the fire on from the remote. Changed the fuse on the fire plug but still nothing.
Did the remote fix as suggested by Mike Evans and Alan R and it works but you do have to wait the 20 mins for it to work. Absolutely delighted!!

Jennyjet747
November 2016

Thank you Alan R. You have just fixed my fire.

CWG.
October 2016

Flamerite fires are fairly rubbish. I have also had 3 circuit boards in my fire. At £55 a time I have now given up with it and it is just an ornament in the wall now. The owner is called David Watts and he is not a particulary pleasant man to deal with. He more or less told me they are made to a price and this is what you must expect.

rick shabin
September 2016

My Cadenza fire has a rattle/noise when i switch the fire on.
how do I get inside the fire ?? Alex

Alex Smethurst
February 2016

flamerite circuit boards last about 4 months absolutely terrible ive had 2 last year and now the fire has gone down again rubbish !!!

james
January 2016

I have a problem with my Flamerite 172/180 Electric Fire. All of a sudden it stopped working. I had a spare Flamerite ERX20 Circuit Board which I have replaced, but it still does not work. Should the DIP settings be the same. One my old board it was on off off on. I have done the remote thing as per Alan R, but no joy.

Gerry
October 2015

no power on lazio fire tested all working remote after fiddling turns lights on breifly before going off have had tester on fire and power going to it any ideas?

||Donna
May 2015

Fault rectified with a replacement PCB direct from Flamerite. The PCB came with a new remote control at a total cost of £62 including VAT and postage.

Mel
February 2015

were can get a new yct-100 remote control

walter barclay
February 2015

When I switch on with the remote, the light flickers and goes off what can I do

Norma kershner
January 2015

Our remote has stopped working may sound daft but how do you get to the batteries

Paul
November 2014

Absolutely brilliant thank you Alan R. I had to get an electrician last time my fire did this you saved me a fortune!

Joan C.G.
September 2014

Hi
Please can you help me. I have a Flamerite Fire model YCT-102. The remote control is not working properly. The only thing it will do is switch the fire on for two seconds when I press the flame button, then it goes off and will not do it again until I switch the fire on manually then off. The on off remote switch does nothing. Please can you help. I have fitted a new battery.

Basil SKINNER
September 2014

I have tried resetting my remote, as although the fire lit up, there was no heat.

Now the fire won't even light up. It is dead!
Are we at the point of a new circuit board?

Can anyone help please?

Donna
June 2014

need a remote control as mine got eaten by the dog if anyone has a spare ?? msands291 at btinternet dot com

mick
March 2014

I've reset my remote and it still doesn't work can anyon help

Sarah
September 2013

I don't no how to switch on my fire can anyone help ??

Sarah
August 2013

Identified:- Three faults on remote controlled fire. Model 86
1. On PCB, triac gate-cathode short circuit fire will not come on at all. Replace with BTA08 600C about £1 to buy from RS
2. On mains connector neutral wire slight corroded, strip back and reconnect
3. Short range control. RF receiver out of tune, space out the turns on the big coil a bit
These cures worked for me. If you are not sure about tackling these faults yourself, buy a new PCB

Michael Denton. med2003 at ntlworld dot com
June 2013

my fire just won't come on the lights flash when turned on at the mains but nothing when i try turning it on by the remote can u help??

stephanie
October 2012

Thank you so much!!
Did what Alan R said and works great.

Steph, Ottawa, Canada
September 2012

done what Alan R said.... worked straight away..thanks!

joanne
September 2012

Who supplies the circuit board in the fire

Henry
August 2012

my flamerite sonata just stoped working just after a year - tried fuse, new remote battery etc any ideas ???

jalag
November 2011

i fixed my flamerite fire, the variable resistor was faulty, so the lights kept flickering, so i removed the light circuit and circulator fan from the circuit board, and rewired them into a seperate switch which I fitted under the fire, at the same time I changed the 4 60w filament bulbs to 4 low energy bulbs, so saving 200w + in use, this modification cost nothing, and saves electric, the heater still works on the remote control, flamerite quoted me £85 callout charge plus £60 parts, i an very happy now with the way the fire works

rob coates
October 2011

it worked for me,cheers,saved me the cost of a new fire!

Sean
August 2011

Does anyone know where i can get an electrical diagram for the yct 100?

ben
February 2011

any idea where one could purchase a new reciever/circuit board??

Jimmy T
January 2011

First reset the fire by switching it off at its own on/off switch, and the mains switch at the socket.

Next reset the remote: undo the Philips screw on the back and prize ip the circuit board, then turn it over, keeping the battery in place. There is a slide switch on the back; move it all the way to the left, pause, then all the way to the right, pause again (10 seconds) then move it about a third of the way to the left until it drops into a detente. Carefully reassemble, keeping the battery in place. If this doesn't work, you probably need a new circuit board (receiver) in the fire. Probably costs about £60. Good luck.

Alan R
December 2010

Hi,my fire comes on 4 a second then goes of again,i changed fuses but no luck,is there a trip on the fire itself?thanks

David.
December 2010

I have similar problem.
Mine switches on but when I try turn on heat II it knocks off, does blow any fuses or trips. When i put trip up and down it will come back on.
Now recently this has started happening when i turn on heat I.

Any further help?

Pat
November 2010

sue,

we have same problem as you. flamerite told us to check the remote as follows: switch fire off at mains, take the back off the remote and inside there is a black switch. slide it to the left and then to the right and then click left. leave for 20 mins and then try all frequencies. this didn't work for us but its worth a try. good luck

MICK EVANS
August 2010