Recent: How to remove battery el3213?

Mend Sentrol 9000 Home Alarm Systems

Mend Security Systems, Home Alarm Systems
Find out how to mend it for free.
Ask Question
Mend Security Systems, Home Alarm Systems
Click here to mend Sentrol 9000 home alarm systems

Mend home alarm systems ...

Mend Security Systems, Home Alarm Systems

How to Reset Optima XM6?

How do you reset the optima xm6 alarm, i know this is done by shorting out 2 terminals on the main board but i... [Read more]
Mend house alarm optima
1

How long does house alarm go for?

I f my optima plus 2 house alarm operates when I am away from home how long will the alarm go on for
Mend Security Systems, Home Alarm Systems

What category of alarm is a scantronic 9884?

what category of alarm is a scantronic 9884+, please?
Mend Security Systems, Home Alarm Systems

How do i deactivate siren on lp1-4000?

how do i deactivate siren on lp1-4000
Mend Security Systems, Home Alarm Systems
3

Scantronics 9450 box stuck shut?

Scantronics 9450 house intruder alarm I cannot get into the box to change the battery. Is there a knack to it?
Mend Home Alarm Systems

Mend > Home Alarm Systems

Mend Sentrol 9000

How do i set zone option "command 8"?

I have a 9000 series alarm and I want to amend the number 3 zone option to include command 8 I have keyed in the engineers code 0 entre 7,8,9,0 and then 3 for zone + "entre" but the desplay does not flash with zone nuber. Can any body help?

Neil
April 2012
SentrolSentrol 9000Security Systems, Home Alarm Systems
Command 8 = Double knock night which allows a detector to trigger either twice in 5 mins or open circuit for longer than 10 seconds. all this info is stated in the installation manual issue 90/3.

Neil
April 2012
Well I've had a good look through the manual and can't find any mention of 'command 8'.

Used this panel since it was introduced back in the dark ages, don't know what you are talking about, I'm keen to find out.

But, I won't hang around here after tomorrow eve (16th)

acorn
April 2012
Sorry, I know the panel that you have, but, Command 8?

Where did you get that from and what is it supposed to do?

Post HERE again and we'll see what we can do.

acorn
April 2012
Mend Security Systems, Home Alarm Systems
Click here to mend Sentrol 9000 home alarm systems
Mend intruder alarm system help

intruder alarm?
Mend Security Systems, Home Alarm Systems

How do i set zone option "command 8"?
Mend security system home alarm zone

alarm not resetting after entering when i have omited a zone?
Mend lost code power

sl 8 accenta alarrm lost code?
Mend security system home security reset

How do I reset my 9651 alarm?
Mend security system panel

how to turn off the alarm when I turn off the electric?
Mend security system zones

How to part set an accenta g4?
Mend switch tamper light fuse

How to switch off Tamper light permanently on in Accenta after fuse change?
Mend hello house remember code

Security?
Mend fitting new sensor

fitting new sensor?
Mend alarm going reason

concept 6 alarm?
Mend stop alarm beeping

How to stop the alarm beeping?

Other models...

Sentrol 9651Sentrol Accenta 6Sentrol Accenta 8Sentrol Accenta+Sentrol Accenta/OptimaSentrol Galaxy 8Sentrol SD1Sentrol SL8Sentrol SL8 AccentaSentrol SL8 G3Sentrol SL8G3Sentrol ST6000

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.

Related Categories

Mend Car Alarm Systems
Car Alarm Systems

Mend Security Systems, Home Alarm Systems
Click here to mend Sentrol 9000 home alarm systems